Pressure Vessel Heads Types Selection And Forming

Product Details
Place of Origin: China
Brand Name: Center Enamel
Certification: ISO 9001,CE, NSF/ANSI 61, WRAS, ISO 28765, LFGB, BSCI, ISO 45001
Payment & Shipping Terms
Minimum Order Quantity: 1 Sets
Price: 2000
Delivery Time: 2 months
Payment Terms: L/C,T/T
Supply Ability: 200 sets / days

Detail Information

Product Description

Pressure Vessel Heads Types Selection And Forming

Pressure vessel heads are the end closures of the pressure boundary, and their geometry governs local stress as much as their thickness does. Selecting the right head is a joint decision between design, forming capability and cost.

This guide covers the head families, how duty drives the choice, the code thickness rules, the forming routes available and the inspection that confirms a formed head matches its specification.

Heads Close The Pressure Boundary

Every pressure vessel needs end closures, and the head is often the most highly stressed part of the assembly. Its curvature determines membrane stress, while the transition to the shell creates a local discontinuity that must be detailed correctly.

Heads are therefore specified as engineered components with their own thickness, material and forming requirements - not as generic stamped shapes selected by diameter alone.

The Main Head Families

Ellipsoidal, torispherical and hemispherical heads are the curved families used on pressure vessels; conical and flat heads serve specific process or low-pressure duties. Each distributes pressure load differently, so each has a different thickness for the same duty.

A hemispherical head develops the lowest membrane stress and can be thinnest; a flat head carries load mainly in bending and becomes heavy at pressure. The choice is a balance of stress efficiency, available forming and the space the vessel occupies.

Selecting Head Geometry By Duty

High-pressure and cyclic services favour geometries with smooth stress distribution and no sharp transition. Where head height is constrained or a shallow closure is needed for layout, a torispherical form may be preferred despite its greater required thickness.

The selection also depends on what the head must carry: a vertical vessel bottom head sees liquid static head and support loads; a top head may carry nozzles, manways or a vent, each adding local stress.

Head Thickness And Code Rules

Codes give specific thickness formulas for each head family based on pressure, radius and allowable stress, with different coefficients reflecting the stress state. The knuckle region of a torispherical head typically governs because it is the least efficient part of the shape.

Forming thins the plate, particularly at the knuckle and crown. The ordered plate must be thick enough that the finished, measured head still meets the minimum required thickness after forming.

Forming Methods And Their Limits

Heads are formed by hot pressing, cold pressing or spinning. Pressing suits thicker plate and smaller quantities; spinning is economical for larger diameters and repeat runs but demands careful thickness control through the shaped zone.

Forming method affects grain structure, residual stress and dimensional accuracy. Some grades and thicknesses require post-forming heat treatment, which must be included in the material and inspection plan.

Crown And Knuckle Stress

In a torispherical head the crown is the central spherical cap and the knuckle is the small-radius transition to the straight flange. A smaller knuckle radius raises stress sharply, which is why codes set a minimum knuckle radius.

Understanding this region explains why two heads of the same diameter and nominal thickness can behave very differently: the one with a tighter knuckle concentrates more stress and may require significantly more plate.

Head To Shell Joint

The circumferential weld joining head to shell is a pressure seam and is treated accordingly in design and examination. Alignment, equal thickness at the joint and a compatible bevel are essential to avoid a step that raises local stress.

Where head and shell are different grades or thicknesses, the joint detail and any transition taper must be designed rather than improvised at fit-up.

Head Inspection And Tolerances

A formed head is checked for thickness across the crown, knuckle and flange, for shape against a template, and for surface defects. The straight-flange length and diameter are measured because they determine fit-up with the shell course.

The inspection record should confirm the minimum measured thickness after forming, not the starting plate thickness. This is the figure the code requirement is judged against.

Head Family By Characteristic

Head

Stress efficiency

Relative depth

Hemispherical

Highest

Deep

2:1 ellipsoidal

Good

Medium

Torispherical

Lower at knuckle

Shallow

Conical

Transition dependent

Variable

Flat

Bending governed

Minimal

Head Specification Inputs

Input

Why it matters

Head family

Sets thickness formula

Inside diameter

Sets geometry

Design pressure

Sets required thickness

Crown / knuckle radius

Governs local stress

Material grade

Sets allowable stress

Forming method

Sets thinning / treatment

Min thickness after forming

Code acceptance

Conclusion

Pressure vessel heads are selected by stress efficiency, forming feasibility and space, then verified by thickness measured after forming - especially at the knuckle, where torispherical designs are least efficient.

State the head family, radii, material and minimum formed thickness in the enquiry; for the geometry-only comparison of dished forms, see the companion article on dished ends.

About Center Enamel

Center Enamel is a pressure vessel and process equipment manufacturer based in China, producing stainless steel and carbon steel pressure vessels, separators, reactors, heat exchangers and storage tanks for chemical, oil and gas, power, food, pharmaceutical and water-treatment applications.

Fabrication is carried out under ASME VIII Div.1, GB/T 150 and ISO 9001 with CE/PED and NACE MR0175 / ISO 15156 options for sour service. Each unit is supplied with material traceability, documented welding procedures, NDT, hydrostatic testing and an export data book.

  • Material range:  Stainless steel (304 / 316L), duplex and carbon steel with rubber or epoxy lining for corrosion duty.
  • Standards:  ASME VIII Div.1, GB/T 150, ISO 9001, CE/PED, NACE MR0175 / ISO 15156.
  • Commercial terms:  Minimum order quantity 1 unit, typical lead time about 2 months, L/C or T/T.

Frequently Asked Questions (FAQ)

What are pressure vessel heads?

The end closures of a pressure vessel; their geometry and thickness determine how pressure load is carried at the ends.

Which head type is strongest?

A hemispherical head has the best stress efficiency and can be thinnest for a given duty, but it is deep and harder to form.

What is a torispherical head?

A head made of a spherical crown, a knuckle of smaller radius and a straight flange; common where a shallow closure is wanted.

What is a 2:1 ellipsoidal head?

An ellipsoidal head whose major and minor axes have a 2:1 ratio, giving a good balance of stress efficiency and depth.

Why does the knuckle matter?

The small-radius knuckle of a torispherical head concentrates stress and usually governs the required thickness.

How is head thickness calculated?

By code formulas specific to each head family using pressure, radius and allowable stress, with allowance for forming thinning.

What is forming thinning?

The reduction in plate thickness as a flat disc is pressed or spun into a curved head, greatest around the knuckle and crown.

Which forming methods are used?

Hot or cold pressing for thicker plate and lower volumes; spinning for larger diameters and repeat production.

When is heat treatment needed after forming?

When the grade, thickness or forming strain requires properties to be restored, as defined by the code and material specification.

How is a head inspected?

Thickness mapping after forming, shape check against a template, surface examination and measurement of flange and diameter.

Can head and shell be different grades?

Yes, but the joint then needs a designed transition in thickness and a compatible weld procedure.

Do flat heads get used at pressure?

Rarely at high pressure, because bending makes them heavy; they suit low-pressure or special process duties.

What tolerance matters most at fit-up?

Diameter and straight-flange length, since they control alignment and high-low at the head-to-shell seam.

Is the starting plate thickness enough evidence?

No; code compliance is judged against the minimum thickness measured on the formed head.

Where can I read the geometry-only comparison?

See the companion dished ends article, which compares ellipsoidal, torispherical and hemispherical geometry and selection.

Suggested CTA: Request a technical quotation with your duty, pressure, temperature and fluid data, or discuss your vessel specification with a Center Enamel engineer for a sized proposal.

Tags: Pressure Vessel Heads, Dished Ends, Pressure Vessel Manufacturer

Want to Know more details about this product
Please enter your inquiry details.
Shijiazhuang Zhengzhong Technology Co., Ltd
sales@cectank.com
86-20-34061629
Fuli Commercial Center room 301#, Xingang West Rd.11#, Haizhu area, Guangzhou, Guangdong province, China.
Leave a Message
*Email
*Message
Send
China Good Quality Glass Fused To Steel Tanks Supplier. Copyright © 2016-2026 cectanks.com . All Rights Reserved.
Send Message