Pressure Vessel Code ASME VIII And EN 13445 Compared

Product Details
Place of Origin: China
Brand Name: Center Enamel
Certification: ISO 9001,CE, NSF/ANSI 61, WRAS, ISO 28765, LFGB, BSCI, ISO 45001
Payment & Shipping Terms
Minimum Order Quantity: 1 Sets
Price: 2000
Delivery Time: 2 months
Payment Terms: L/C,T/T
Supply Ability: 200 sets / days

Detail Information

Product Description

Pressure Vessel Code ASME VIII And EN 13445 Compared

A pressure vessel code is the rule set that governs how a vessel is designed, built, inspected and tested. Choosing the right one is a contractual and legal decision that shapes thickness, material, welding and documentation.

This guide compares the four codes most often encountered in international procurement and explains what actually differs - not just which countries use them.

What A Pressure Vessel Code Defines

A code sets minimum rules for design stress, material acceptance, joint design, fabrication practice, examination and pressure testing. It does not replace engineering judgement, but it defines the boundary within which a compliance claim is valid.

Codes also define who may certify the vessel and what documentation proves conformity. That is why a vessel built to one code cannot simply be relabelled for another market at shipment.

ASME BPVC Section VIII Division 1

Division 1 is a rule-based code used for a very wide range of process vessels. Its UG sections give direct formulas for shells, heads and reinforcement, with allowable stresses drawn from the material tables of Section II.

It is widely recognised, supported by an extensive supplier base, and often specified even where it is not the local legal requirement. Its conservative rules make it straightforward to apply but sometimes heavier than an analysis-based alternative.

ASME Division 2 Alternative Rules

Division 2 is an analysis-based route that permits higher allowable stress by applying stricter requirements on materials, design detail, fabrication and examination. The result can be a lighter vessel for high-pressure or fatigue-sensitive service.

The saving is paid for with more engineering and more testing. Division 2 is chosen when the duty genuinely warrants it, not as a way to cut plate without accepting the associated analytic and inspection burden.

EN 13445 And The PED

EN 13445 is the harmonised European standard for fired and unfired pressure vessels and provides a route to meet the Pressure Equipment Directive. It offers three design paths: formula-based, direct/analytical and stress-analysis based.

The PED classifies equipment by hazard and applies conformity assessment accordingly, so the same vessel design can carry different obligations depending on its pressure-volume category and fluid group.

GB/T 150 In China

GB/T 150 is the Chinese national standard for pressure vessels, issued in parts covering materials, design, manufacture and inspection. It is the default for domestic projects and is frequently used for export vessels built in China.

Its structure and allowable-stress philosophy differ from ASME, so a vessel cannot be assumed equivalent simply because the thickness looks similar; the material system and test requirements must be compared item by item.

Key Technical Differences

The main differences lie in allowable-stress basis, weld joint efficiency, material designation and the required pressure-test multiple. Some codes credit full radiography more generously; others set different minimum test temperatures or hold times.

Material identification also differs: ASME uses P-Numbers and SA specifications, EN uses steel names and numbers under EN 10028, and GB/T uses its own grade system. Equivalence must be demonstrated, not assumed by name.

Choosing The Code For A Project

The governing code follows the installation jurisdiction, the client's specification and any applicable directive. Where the client leaves a choice, the decision should weigh regulatory acceptance, local inspector availability and the shop's demonstrated experience.

Changing code after design release is a major change: it can alter thickness, material, weld examination and documentation, so it belongs at the enquiry stage rather than after award.

Code Compliance And The Data Report

Compliance is demonstrated through the data report and the as-built dossier, not through a statement on a drawing. For ASME vessels this includes the manufacturer's data report and, where applicable, the code symbol stamp and authorized inspector involvement.

A buyer should confirm that the supplier can issue the exact report and marking the chosen code requires, and that the named inspection body is acceptable to the destination authority.

Pressure Vessel Code Comparison

Code

Design basis

Typical market

ASME VIII Div.1

Rule-based

International / North America

ASME VIII Div.2

Stress analysis

High pressure / cyclic

EN 13445

Formula / direct / analysis

EU under PED

GB/T 150

Rule-based

China

Code Selection Inputs

Input

Effect

Installation country

Sets legal code

Client specification

May name code / edition

Fluid group

Sets hazard category

Pressure-volume

Sets conformity route

Cyclic duty

May favour Div.2

Inspector availability

Affects certification

Shop experience

Affects execution risk

Conclusion

ASME VIII, EN 13445 and GB/T 150 are not interchangeable labels. They differ in stress basis, materials, examination and the documents that prove compliance, and the choice must be fixed before design begins.

Select the code by jurisdiction and client requirement first, then confirm the supplier can deliver the exact data report and marking that code demands.

About Center Enamel

Center Enamel is a pressure vessel and process equipment manufacturer based in China, producing stainless steel and carbon steel pressure vessels, separators, reactors, heat exchangers and storage tanks for chemical, oil and gas, power, food, pharmaceutical and water-treatment applications.

Fabrication is carried out under ASME VIII Div.1, GB/T 150 and ISO 9001 with CE/PED and NACE MR0175 / ISO 15156 options for sour service. Each unit is supplied with material traceability, documented welding procedures, NDT, hydrostatic testing and an export data book.

  • Material range:  Stainless steel (304 / 316L), duplex and carbon steel with rubber or epoxy lining for corrosion duty.
  • Standards:  ASME VIII Div.1, GB/T 150, ISO 9001, CE/PED, NACE MR0175 / ISO 15156.
  • Commercial terms:  Minimum order quantity 1 unit, typical lead time about 2 months, L/C or T/T.

Frequently Asked Questions (FAQ)

What is a pressure vessel code?

A rule set governing design stress, materials, fabrication, examination and testing, plus the certification needed to claim compliance.

Which code is most widely used?

ASME Section VIII Division 1 is specified on many international projects, but the legal code is the one required at the place of installation.

What is the PED?

The European Pressure Equipment Directive, which classifies equipment by hazard and sets conformity assessment routes; EN 13445 is a harmonised standard for vessels.

What is ASME Division 2?

An analysis-based alternative permitting higher allowable stress with stricter material, design, fabrication and examination requirements.

Is EN 13445 equivalent to ASME VIII?

Not directly. Design paths, material systems, test requirements and documentation differ, so equivalence must be evaluated item by item.

What is GB/T 150?

The Chinese national pressure vessel standard, issued in parts for materials, design, manufacture and inspection.

Why does joint efficiency differ between codes?

Codes credit weld examination to different degrees, which changes the permitted stress and therefore the required thickness.

Can a vessel be built to two codes at once?

It can be designed to satisfy both, but a single compliance claim must name one code; dual claims require both full document sets.

What is a P-Number?

An ASME grouping of materials used to qualify welding procedures; similar groups share qualification rules.

What proves code compliance?

The manufacturer's data report, the as-built dossier and, where required, the code stamp and authorized inspector sign-off.

Can a code be changed after award?

Technically possible but disruptive: thickness, material, examination and documents can all change, so decide at enquiry stage.

Does a code guarantee safety?

It sets minimum accepted rules; safe operation also depends on correct duty definition, operation within rating and maintenance.

Who appoints the inspector?

It depends on the code and jurisdiction; the purchaser or the destination authority often defines the acceptable inspection body.

What should an enquiry state?

Installation country, governing code and edition, fluid group, design pressure and temperature, and required certification.

How does code affect lead time?

Analysis-based routes and third-party inspection add engineering and scheduling steps; an engineered vessel is commonly quoted around two months.

Suggested CTA: Request a technical quotation with your duty, pressure, temperature and fluid data, or discuss your vessel specification with a Center Enamel engineer for a sized proposal.

Tags: Pressure Vessel Code, ASME Pressure Vessel, Pressure Vessel Manufacturer

Want to Know more details about this product
Please enter your inquiry details.
Shijiazhuang Zhengzhong Technology Co., Ltd
sales@cectank.com
86-20-34061629
Fuli Commercial Center room 301#, Xingang West Rd.11#, Haizhu area, Guangzhou, Guangdong province, China.
Leave a Message
*Email
*Message
Send
China Good Quality Glass Fused To Steel Tanks Supplier. Copyright © 2016-2026 cectanks.com . All Rights Reserved.
Send Message