CE Marked Pressure Vessel Marking Steps And Declaration

Product Details
Place of Origin: China
Brand Name: Center Enamel
Certification: ISO 9001,CE, NSF/ANSI 61, WRAS, ISO 28765, LFGB, BSCI, ISO 45001
Payment & Shipping Terms
Minimum Order Quantity: 1 Sets
Price: 2000
Delivery Time: 2 months
Payment Terms: L/C,T/T
Supply Ability: 200 sets / days

Detail Information

Product Description

CE Marked Pressure Vessel Marking Steps And Declaration

A CE marked pressure vessel has passed the conformity assessment required by the Pressure Equipment Directive 2014/68/EU and carries the declaration and marking that allow it to be placed on the EU market.

This guide covers the practical marking sequence - classification, module, notified body, technical file, declaration and mark placement - as the operational companion to the directive framework article.

CE Marking Is A Manufacturer's Declaration

Affixing the CE mark is the manufacturer's declaration that the product meets the applicable EU harmonised legislation. It is not a certificate issued by a laboratory or a notified body.

For pressure equipment the legal basis is Directive 2014/68/EU, and the mark may be applied only after the applicable conformity assessment has been completed.

Step One: Confirm Scope And Category

First confirm the equipment is in scope, generally above 0.5 bar maximum allowable pressure, then determine the fluid group and use pressure and volume to assign the category.

The category decides how demanding the conformity route is and whether a notified body must be involved; getting it wrong invalidates the subsequent steps.

Step Two: Choose The Conformity Module

The directive offers modules that combine design and production assessment in different ways. The category determines which modules are available, from internal production control to full quality assurance with notified body involvement.

The chosen module defines exactly what the manufacturer must document and what a third party must verify, so it is selected before assessment begins.

Step Three: Apply Harmonised Standards

The manufacturer applies harmonised standards such as EN 13445 where relevant to demonstrate the essential requirements, or documents an equivalent technical solution.

The standards cited in the Official Journal change over time, so the current references must be checked and recorded in the technical file.

Step Four: Notified Body Where Required

For categories and modules that require it, a notified body examines the design and/or the production quality system and issues the certificates needed for the file.

A notified body is designated by a member state for specific product areas, so the buyer should confirm it is notified for pressure equipment, not merely an independent certification provider.

Step Five: Technical File And Declaration

The technical file collects the design, calculations, material records, examination and test results, risk assessment and standards applied. The manufacturer then drafts the EU declaration of conformity.

The declaration must identify the product, the directive, the harmonised standards used, the notified body where involved and the signatory, and it must be kept with the file.

Step Six: Mark Placement And Traceability

The CE mark is applied by the manufacturer in a visible, legible and permanent form, together with the identification of the manufacturer and the notified body where applicable.

The vessel's nameplate must remain traceable to the declaration and technical file; a mark without that supporting documentation is not meaningful.

Common Errors To Avoid

Frequent problems include treating a supplier's 'CE certificate' as the compliance basis, using an outdated directive number, and failing to match the declaration to the exact vessel supplied.

Only notified bodies may issue certificates within their notified scope under EU law, and the CE mark itself is applied by the manufacturer after assessment.

CE Marking Sequence

Step

Output

Third party

Scope / category

Classification record

No

Module

Assessment route

Depends

Standards

Design evidence

No

Assessment

Certificate if required

Notified body

Declaration

EU DoC

No

Marking

Marked vessel + file

No

CE Marking Checklist

Item

Requirement

Directive

2014/68/EU (not 2014/610/EU)

Category

From fluid, PS, volume

Conformity module

Matched to category

Harmonised standard

Current OJ reference

Notified body

Only where required

Technical file

Complete evidence

EU declaration

Signed, product-specific

Conclusion

A CE marked pressure vessel is the result of a defined sequence: scope and category, conformity module, harmonised standards, notified body where required, technical file, declaration and mark placement.

Use the correct directive 2014/68/EU, confirm the notified body's scope, and insist that the declaration and technical file match the exact vessel delivered.

About Center Enamel

Center Enamel is a pressure vessel and process equipment manufacturer based in China, producing stainless steel and carbon steel pressure vessels, separators, reactors, heat exchangers and storage tanks for chemical, oil and gas, power, food, pharmaceutical and water-treatment applications.

The company works under ASME VIII Div.1, GB/T 150 and ISO 9001, and can supply CE/PED marking for the EU market with material traceability, documented welding procedures, NDT and hydrostatic testing in the delivered data book.

  • Certifications: ASME, ISO 9001, CE/PED, NSF/ANSI 61, WRAS, ISO 28765, LFGB, BSCI, ISO 45001.
  • Standards: ASME VIII Div.1, GB/T 150, EN 13445 where required by the destination market.
  • Commercial terms: Minimum order quantity 1 unit, typical lead time about 2 months, L/C or T/T.

Frequently Asked Questions (FAQ)

What is a CE marked pressure vessel?

A vessel that has completed the conformity assessment under 2014/68/EU and carries the manufacturer's declaration and CE mark for EU market access.

Who issues the CE mark?

The manufacturer applies it after completing the assessment; it is not a certificate issued by a third party.

Which directive applies?

Directive 2014/68/EU, the Pressure Equipment Directive. '2014/610/EU' is an incorrect citation.

When is a notified body required?

In the categories and modules where the directive calls for third-party design or production assessment.

What is a conformity module?

A defined route in the directive combining design and production assessment obligations.

What is the technical file?

The design, calculation, material, examination, test and standards evidence supporting the declaration.

What is the EU declaration of conformity?

A signed document identifying the product, directive, standards and, where relevant, the notified body, issued by the manufacturer.

Is a supplier CE certificate enough?

No. The manufacturer's declaration and technical file are the compliance basis, not a generic certificate.

Can any lab issue a PED certificate?

Only notified bodies designated for the relevant product area may issue certificates within their notified scope.

Where must the mark be placed?

Visibly, legibly and permanently on the product or its nameplate, traceable to the declaration.

Does CE replace process design?

No. Process conditions remain a separate specification; PED addresses safety and market access.

Which standard demonstrates the requirements?

Commonly a harmonised standard such as EN 13445, or an equivalent documented solution.

Are harmonised standards current permanently?

No. References are updated in the Official Journal and must be checked at assessment time.

What should a buyer request?

The declaration, the category and module basis, the standard references and the nameplate data matching the vessel.

How long does a CE vessel take?

About two months from a China manufacturer for an engineered vessel, subject to assessment scope.

Suggested CTA: Request a technical quotation with your duty, pressure, temperature and fluid data, or discuss the applicable code and marking route with a Center Enamel engineer.

Want to Know more details about this product
Please enter your inquiry details.
Shijiazhuang Zhengzhong Technology Co., Ltd
sales@cectank.com
86-20-34061629
Fuli Commercial Center room 301#, Xingang West Rd.11#, Haizhu area, Guangzhou, Guangdong province, China.
Leave a Message
*Email
*Message
Send
China Good Quality Glass Fused To Steel Tanks Supplier. Copyright © 2016-2026 cectanks.com . All Rights Reserved.
Send Message